Altera IC Unlock — What Is Actually Recoverable?
Altera IC unlock refers to the authorized extraction of configuration bitstreams or embedded firmware from Altera (now Intel PSG) CPLDs and FPGAs. Our engineers recover data from devices where the original design files have been lost, the designer is unavailable, or a legacy product must be maintained. Recovery is performed under NDA with proof of IP ownership — we do not assist with unauthorized extraction of third-party designs.
Altera devices range from simple MAX-series CPLDs with relatively straightforward non-volatile configuration storage to Cyclone and Stratix FPGAs whose bitstreams are loaded from external flash at power-up. The protection level, device generation, and configuration method determine whether a given Altera IC unlock is feasible and how long it takes.
Which Altera Families Can We Unlock?

Not every Altera part is equally recoverable. The table below summarizes the families we work with most frequently, the dominant protection scheme each uses, and our typical success outlook.
| Family | Common Parts | Protection Mechanism | Recovery Outlook |
|---|---|---|---|
| MAX 7000 / 7000S | EPM7032, EPM7064, EPM7128, EPM7256 | Security bit (JTAG disable) | High — mature process, well-understood fuse structure |
| MAX II | EPM240, EPM570, EPM1270, EPM2210 | CFM sector lock + ISP lock | High — non-volatile flash-based; multiple attack vectors documented |
| MAX V | 5M40Z, 5M80Z, 5M160Z, 5M240Z, 5M570Z | CFM sector lock + ISP lock | High — similar architecture to MAX II |
| MAX 10 | 10M02, 10M04, 10M08, 10M16, 10M25, 10M50 | AES-128 bitstream encryption + JTAG lock | Moderate — unencrypted parts recoverable; AES-locked parts require key or case-by-case evaluation |
| Cyclone / Cyclone II | EP1C3–EP1C20, EP2C5–EP2C70 | External config flash (no on-chip NVM) | High — bitstream lives in SPI/parallel flash; we read the flash directly |
| Cyclone III / IV | EP3C5–EP3C120, EP4CE6–EP4CE115 | External flash, optional AES-128 encryption | High if unencrypted; moderate if AES key is stored in volatile SRAM key register |
| Cyclone V | 5CEBA / 5CGXFC / 5CSEMA (SoC) | AES-256 encryption, Secure Device Manager | Low to moderate — heavily dependent on whether encryption was actually enabled |
| ACEX 1K | EP1K10–EP1K100 | External config PROM / passive serial | High — legacy SRAM-based; config stored off-chip |
| FLEX 10K / 10KE | EPF10K10–EPF10K200 | External EPC-series config PROM | High — read the EPC device directly |
| Stratix / Stratix II | EP1S10–EP1S80, EP2S15–EP2S180 | External flash, optional AES-128 | Case-by-case — large bitstreams, encryption varies |
If your specific part number is not listed, submit a free feasibility request — we evaluate Altera devices on a per-part basis and return an honest assessment within 1–2 working days.
How Altera Protection Mechanisms Work
Security Fuse / Security Bit (Legacy CPLDs)
Older Altera CPLDs such as the MAX 7000 family use a single programmable security fuse. When set, this bit blocks JTAG readback of the internal configuration. Our lab techniques can bypass this fuse on most MAX 7000-era devices with a success rate above 90 %, depending on the specific process node (0.35 µm EEPROM vs. 0.18 µm flash). The extraction is non-destructive in most cases — the original device continues to function.
CFM Sector Lock (MAX II / MAX V)
MAX II and MAX V parts store their configuration in internal user flash memory (UFM) and configuration flash memory (CFM). Intel’s ISP lock and sector-lock bits prevent standard JTAG readback. However, because these are single-chip, non-volatile devices with no encryption engine, our engineers have reliable methods for recovering the full bitstream. Turnaround is typically 5–8 working days.
AES Bitstream Encryption (Cyclone III+ / Stratix / MAX 10)
Starting with Cyclone III, Altera introduced optional AES-128 (later AES-256) bitstream encryption. The FPGA stores a decryption key in volatile SRAM (battery-backed) or in non-volatile fuses. If the bitstream in external flash is encrypted and the key is volatile, recovery requires that the key battery still holds charge — once the key is lost, the encrypted bitstream cannot be decrypted by any known means. We are transparent about this limitation upfront.
For devices where encryption was available but never actually enabled by the designer — which is surprisingly common on cost-sensitive products — the bitstream sits in plain form in the external SPI flash and can be read with standard tools. Our first diagnostic step is always to read the configuration memory or flash and check for encryption signatures.
Our Altera IC Unlock Process
- Feasibility assessment — You send us the part number (e.g., EPM570T100C5N), a board photo, and proof of ownership. We return a written feasibility opinion within 1–2 business days at no charge.
- Device receipt & inspection — We receive the physical board or loose device, inspect for damage, verify the part marking, and identify the configuration path (on-chip NVM, external flash, or config PROM).
- Security analysis — Our engineers probe the JTAG chain, read external configuration memory if present, and determine whether encryption or lock bits are active.
- Bitstream extraction — Using device-specific techniques (fuse bypass, glitch-based attacks on unencrypted parts, direct flash readout), we extract the raw bitstream or JEDEC/POF/SVF file.
- Verification — The recovered file is programmed into a blank device of the same part number and functionally verified against the original board’s behavior.
- Delivery — We deliver the bitstream in your preferred format (SOF, POF, JIC, SVF, or raw binary) along with a summary report. All files are transferred via encrypted channel under NDA.
Typical turnaround for a straightforward MAX II or Cyclone external-flash read is 5–8 working days. Complex cases involving Cyclone V SoC or encrypted Stratix parts may take 10–15 days and carry a higher fee reflecting the additional engineering effort.
What Can Go Wrong — Honest Limitations

- AES-encrypted bitstream with lost volatile key: If the SRAM key has been erased (battery dead, power removed without backup), recovery is not possible. We will tell you this before you spend money.
- Physically damaged die: Corrosion, ESD damage, or decapsulation attempts by other labs can render the silicon unreadable. We assess damage before committing.
- Newer Intel Agilex / Stratix 10 parts: These use Secure Device Manager with PUF-based key storage and encrypted fuse banks. We do not currently offer recovery for these families.
- Partial configuration: Some Cyclone designs use partial reconfiguration. We can extract the full initial bitstream but may not capture runtime-loaded partial images unless they are also stored in flash.
Altera vs. Other Programmable-Logic Vendors
Altera CPLDs and FPGAs are not the only programmable-logic devices we work with. If your board contains parts from other vendors alongside an Altera device, we can often handle the entire board in one project. For example, we also support Lattice ECP and MachXO readback and QuickLogic eFPGA bitstream recovery. On mixed-signal boards, you might also find companion MCUs from vendors like Maxim Integrated or analog front-ends from ON Semiconductor devices — all of which we handle under the same NDA and project scope.
Authorization & Legal Requirements
We perform Altera IC unlock only for authorized parties: the original IP owner recovering lost source files, a licensee with documented rights, or a company maintaining its own legacy hardware. Before we begin work, we require a signed NDA and a declaration of ownership or authorization. This protects both parties and ensures compliance with applicable IP law.
If you have questions about what documentation is needed, our team can walk you through the process — most clients complete the paperwork in under a day.
Deliverable Formats
| Format | Use Case |
|---|---|
| .sof (SRAM Object File) | Direct JTAG programming of Cyclone / Stratix FPGAs |
| .pof (Programmer Object File) | Programming MAX II / MAX V / MAX 10 internal flash |
| .jic (JTAG Indirect Config) | Programming external SPI flash via JTAG chain |
| .svf (Serial Vector Format) | Vendor-neutral JTAG playback for production programming |
| .rbf / .bin (Raw Binary) | Passive serial or custom bootloader use |
| .jedec (JEDEC Standard) | Legacy CPLD programming (MAX 7000) |
We default to the native Quartus-compatible format for your device but can convert to any of the above on request.
Check feasibility for your project
Send the chip marking or board details and tell us what you need to recover. Add clear photos if available.
Request a feasibility reviewCan you recover the bitstream from an encrypted Cyclone IV?
It depends on whether encryption was actually enabled. Many Cyclone IV designs ship with AES encryption available but not configured — the bitstream in external flash is plaintext and fully recoverable. If AES-128 is active and the volatile key is intact, recovery may still be possible. If the key battery is dead, the encrypted bitstream cannot be decrypted. We check encryption status as part of our free feasibility assessment.
Is Altera IC unlock legal?
Yes, when performed for authorized purposes — recovering your own lost design data, maintaining legacy equipment you own, or acting under a license from the IP holder. We require proof of ownership or authorization and work under NDA. We do not assist with extracting third-party proprietary designs without documented permission.
How long does an Altera CPLD readout take?
For MAX II and MAX V CPLDs, typical turnaround is 5–8 working days from the time we receive the device. MAX 7000-series parts are often faster — 3–5 days — due to simpler protection. Complex FPGA cases (Cyclone V SoC, Stratix) can take 10–15 working days. We confirm the timeline in our feasibility report before you commit.
Do you need the whole board or just the chip?
For CPLDs (MAX II, MAX V, MAX 7000), we can work with either the full board or a desoldered chip. For SRAM-based FPGAs (Cyclone, Stratix) whose bitstream lives in an external flash, sending the entire board is preferred so we can read the configuration memory in-circuit. If desoldering is required, our technicians handle it — you do not need to remove parts yourself.
What if my Altera device is obsolete and I cannot find a replacement?
Recovering the bitstream is the first step. Once we have the configuration file, we can also assist with migrating the design to a pin-compatible or functionally equivalent current-production part — for example, moving from a discontinued EPM7128 to a MAX II EPM240 with logic re-synthesis. This is quoted as a separate engineering service after the initial readout.
For firmware recovery on other IC families often found alongside Altera FPGAs, see our guides on Toshiba TLCS-870 and TMP86 extraction and Sinowealth SH79F and SH68F readout.
What do you need to recover?
Send the full marking or board photos, sample condition and required outcome. Ask for an NDA before sharing confidential files. Scope and sample handling are confirmed individually.
The article title is carried into the contact form. Add your own details and review the enquiry before sending.