What Is AT90 Unlock and When Do You Need It?
AT90 unlock is the process of reading protected firmware from Atmel (now Microchip) AT90-series AVR microcontrollers whose lock bits have been set to prevent external access. Engineers typically need this service when original source code is lost, a key developer has left the company, or a legacy product requires maintenance on a discontinued board. Our lab recovers flash and EEPROM contents from locked AT90 devices for clients who can demonstrate ownership or authorization of the target design.
AT90 Family Overview and Protection Mechanisms

The AT90 designation covers a range of 8-bit AVR parts, each with slightly different flash sizes, peripherals, and—critically—different lock-bit configurations. All AT90 devices share the same fundamental protection scheme inherited from the classic AVR architecture: two lock-bit pairs (LB1/LB2) that restrict read and write access through ISP, JTAG, or debugWIRE interfaces.
Key AT90 Variants We Encounter
| Part Number | Flash (KB) | Package | Lock-Bit Modes | Unlock Feasibility |
|---|---|---|---|---|
| AT90S2313 | 2 | DIP-20 / SOIC-20 | Mode 1–3 | High |
| AT90S8515 | 8 | DIP-40 / TQFP-44 | Mode 1–3 | High |
| AT90S8535 | 8 | DIP-40 / TQFP-44 | Mode 1–3 | High |
| AT90CAN32 | 32 | TQFP-64 | Mode 1–3 | Moderate–High |
| AT90CAN64 | 64 | TQFP-64 | Mode 1–3 | Moderate |
| AT90CAN128 | 128 | TQFP-64 | Mode 1–3 | Moderate |
| AT90USB646 | 64 | TQFP-64 / QFN-64 | Mode 1–3 | Moderate |
| AT90USB1286 | 128 | TQFP-64 / QFN-64 | Mode 1–3 | Moderate |
| AT90PWM316 | 16 | SOIC-32 / QFP-32 | Mode 1–3 | High |
Mode 3 lock bits disable both ISP and JTAG read access simultaneously. Older AT90S-series parts (manufactured on larger process nodes, 0.35 µm or above) are generally more amenable to physical-layer techniques than the newer AT90USB or AT90CAN parts built on 0.18 µm processes.
How AVR Lock Bits Work
AVR lock bits are stored in a dedicated fuse area outside the main flash array. When LB mode 3 is programmed, the chip blocks all external read paths—ISP, JTAG, and parallel programming. A standard chip-erase clears the lock bits but simultaneously wipes flash and EEPROM, making it useless for recovery. Our AT90 unlock techniques bypass or circumvent these restrictions without triggering the erase sequence.
How Our Engineers Perform AT90 Unlock
Every AT90 unlock engagement follows a structured workflow designed to maximize data integrity and minimize risk to the silicon.
- Feasibility assessment (Day 1–2): We identify the exact part marking, revision, and date code. Die revision matters—an AT90CAN128 from 2006 may respond differently than one from 2012.
- Decapsulation (if required): For parts requiring physical access, we perform chemical or laser decapsulation to expose the die without damaging bond wires or the flash array.
- Protection bypass: Using micro-probing, UV exposure (older EPROM-windowed variants), voltage glitching, or proprietary fault-injection techniques, we disable or bypass the lock-bit enforcement logic.
- Readout and verification: Flash and EEPROM contents are read, then verified with a CRC or checksum comparison across multiple passes. We deliver only data that passes our three-pass consistency check.
- Delivery: Firmware is provided as an Intel HEX or raw binary file along with fuse-byte and lock-bit documentation.
For the older AT90S-series, UV-based techniques can work in under 24 hours of bench time. The AT90USB and AT90CAN families require more sophisticated fault injection, adding 3–5 days to the process.
AT90 Unlock Cost and Lead Time
Pricing depends on the specific variant, lock-bit mode, and die revision. Below are representative ranges based on recent projects.
| Category | Typical Cost (USD) | Lead Time (Working Days) |
|---|---|---|
| AT90S-series (2313, 8515, 8535) | $400 – $700 | 5 – 7 |
| AT90PWM-series | $500 – $900 | 5 – 8 |
| AT90CAN32/64 | $600 – $1,200 | 7 – 10 |
| AT90CAN128 | $800 – $1,500 | 7 – 12 |
| AT90USB646/1286 | $800 – $1,800 | 8 – 12 |
We charge a flat evaluation fee of $50–$100 that is credited toward the full project if you proceed. If we determine the chip cannot be unlocked—due to die damage, blown security fuses on newer revisions, or other physical constraints—you pay only the evaluation fee.
What Can Go Wrong?
Transparency matters. Here are the realistic failure modes our engineers encounter during AT90 unlock work:
- Die damage during decapsulation: Aggressive acid exposure or over-etching can sever bond wires. Our success rate on decapsulation alone exceeds 95%, but it is not 100%.
- Partially corrupted flash: If the device experienced latch-up or ESD events before reaching our lab, certain flash sectors may already be unreadable regardless of lock-bit state.
- Newer die revisions with enhanced countermeasures: Some late-production AT90CAN128 and AT90USB1286 parts include additional glitch-detection circuitry not documented in public datasheets. These can require multiple sample chips and extended R&D time.
- EEPROM wear: On devices that used EEPROM heavily, cell degradation may yield inconsistent reads. We flag suspect bytes in our deliverable report.
We always recommend sending at least two sample chips when possible—one for primary extraction and one as a backup in case the first is consumed during physical-layer work.
Authorization and Legal Requirements

AT90 unlock is performed strictly for authorized parties. Before we begin, you must provide proof that you own the design, are the original manufacturer, or hold written authorization from the IP holder. All projects are covered by our mutual NDA. For full details on our compliance framework, see our authorization and trust policy.
Common authorized use cases include:
- Recovering firmware for a product you designed but whose source was lost.
- Maintaining or repairing legacy equipment where the original vendor is defunct.
- Migrating firmware to a pin-compatible replacement MCU (e.g., moving from AT90CAN128 to an ATmega128).
AT90 vs. Related Atmel/Microchip Families
The AT90 series sits alongside several other Atmel AVR and ARM-based families. If you are unsure which part you have, or if your board uses a mix of controllers, these related pages may help:
- Microchip’s 32-bit ARM Cortex-M0+ parts use a completely different protection model. See our page on ATSAMD21 firmware recovery for details on those SWD-locked devices.
- The ATSAM4 family (Cortex-M4) adds flash security bits and GPNVM protection. Our ATSAM4 unlock guide covers the differences.
- For Cortex-M7 based ATSAM3 devices, the protection architecture changes again—covered in our ATSAM3 unlock overview.
If your target is an ATmega or ATtiny rather than an AT90, contact us with the full part number. The lock-bit architecture is similar, but die-level differences affect technique selection and cost.
Deliverables You Receive
- Firmware image: Intel HEX (.hex) and raw binary (.bin) files covering the full flash range.
- EEPROM dump: Separate file if the device contains EEPROM data.
- Fuse and lock-bit report: Exact values of LFUSE, HFUSE, EFUSE, and lock bits as read from the device.
- Integrity report: CRC32 checksums, read-pass consistency notes, and any flagged suspect addresses.
All files are delivered via encrypted transfer. We retain no copies after 30 days unless you request archival.
How to Get Started
Send us your AT90 part number, board photos (if available), and a brief description of your recovery need. Our engineers will respond within one business day with a feasibility opinion and a firm quote. For projects involving other locked MCUs on the same board, we handle multi-chip engagements under a single NDA and project scope.
Check feasibility for your project
Send the chip marking or board details and tell us what you need to recover. Add clear photos if available.
Request a feasibility reviewCan you unlock every AT90 variant?
We support most AT90S, AT90CAN, AT90USB, and AT90PWM parts. Older AT90S devices (manufactured before ~2005 on 0.35 µm process) have the highest success rates. Late-revision AT90USB1286 parts with enhanced glitch detection may require extended R&D. We always confirm feasibility before charging the full project fee.
Will the AT90 chip be destroyed during unlock?
It depends on the technique. Non-invasive methods (voltage glitching, timing attacks) leave the chip functional. Invasive methods requiring decapsulation render the package unusable, though the extracted firmware can be programmed into a fresh AT90 device. We recommend sending a spare when possible.
How do I prove I own the firmware on the AT90?
Acceptable documentation includes a purchase order for the original development, a design-house contract naming you as the IP owner, a letter of authorization from the rights holder, or proof that you manufactured the board. We review documentation before beginning any work.
Can you reprogram the recovered firmware into a new AT90 chip?
Yes. Once we extract the HEX file, we can program it into blank AT90 devices of the same part number and set the fuse bits to match the original configuration. We can also assist with migration to compatible AVR parts if the original AT90 variant is discontinued.
What if my board also has a locked GD32 or CH32 MCU?
We handle multi-chip recovery regularly. For GD32-based boards, see our GD32F4 unlock page. For WCH CH32 parts, our CH32F unlock service covers the process. We scope all chips under one project to reduce cost and turnaround.
Working on a board like this?
Send the chip marking or two photos. You get feasibility, lead time and price within 24 hours, and the check costs nothing.
Get a free quote