Bao'An Shenzhen China

C2000 Unlock | Feasibility, Cost & Lead Time

Published · About 8 min read · PCB-Copy

On this page
  1. What Is C2000 Unlock and When Do You Need It?
  2. How Does TI Protect C2000 Flash?
  3. C2000 Unlock Feasibility by Sub-Family
  4. What Determines Cost and Lead Time?
  5. Our C2000 Unlock Process — Step by Step
  6. Authorization Requirements for C2000 Unlock
  7. Common Failure Modes and Honest Limitations
  8. C2000 vs. Other DSP/MCU Families
  9. Deliverables You Receive
  10. Frequently Asked Questions
  11. Related IC Unlock Services

What Is C2000 Unlock and When Do You Need It?

C2000 unlock is the process of reading protected firmware from Texas Instruments’ TMS320F28x real-time control DSPs. Engineers typically need this service to recover lost source code from legacy motor-drive or power-converter boards, restore production capability after a key developer leaves, or migrate firmware from an obsoleted C2000 variant to a current one. Our lab handles authorized C2000 unlock requests with turnaround times of 5–15 working days and costs starting around $500–$3,000 depending on the specific device and its protection level.

How Does TI Protect C2000 Flash?

c2000 unlock: TMS320F28335 C2000 DSP chip on a motor-control PCB ready for firmware recovery

Texas Instruments has evolved C2000 code protection significantly across generations. Understanding the specific mechanism on your chip is the single biggest factor in determining whether an unlock is feasible.

Code Security Module (CSM) — Older F28xx Devices

The original Code Security Module uses a 128-bit password stored in a dedicated flash location. When CSM is engaged, JTAG read access to flash and OTP is blocked until the correct password is written to the CSM registers. Devices using CSM include the F2801, F2802, F2806, F2808, F2810, F2811, F2812, and early F28335 revisions.

CSM-protected parts are the most approachable for recovery. The password resides in a known flash sector, and several well-documented attack vectors exist — from voltage-glitch-assisted JTAG reactivation to semi-invasive probing of the password location. Our success rate on CSM-only devices exceeds 90%.

Dual-Code Security Module (DCSM) — Newer F28x7x / F28x0x

Starting with the F2837xD/S and continuing through the F28004x, F28002x, and F28003x families, TI introduced DCSM. This splits flash into two independent security zones (Zone 1 and Zone 2), each with its own 128-bit password, plus a dedicated “link pointer” scheme that controls which flash sectors belong to which zone. DCSM also supports EXEONLY protection — sectors that can execute but never be read back, even with the correct password.

DCSM is substantially harder to defeat. EXEONLY sectors, when properly configured, have no known non-destructive readout path. However, many production boards leave EXEONLY disabled or misconfigure the link pointers, which gives our engineers a viable attack surface. Feasibility is device- and configuration-specific — we need the actual chip in hand to assess it.

Secure Boot and CMAC — F29xx / AM263x Transition

The newest C2000-adjacent devices (marketed under the AM263x and F29H85x umbrella) add hardware root-of-trust with CMAC authentication. These parts are currently beyond practical unlock capability for any lab. If your device falls in this category, we will tell you upfront during the free feasibility check rather than waste your time.

C2000 Unlock Feasibility by Sub-Family

Sub-Family Protection Type Feasibility Typical Lead Time Cost Range (USD)
F2801 / F2802 / F2806 CSM 128-bit High (>90%) 5–8 days $500–$900
F2808 / F2810 / F2811 / F2812 CSM 128-bit High (>90%) 5–8 days $500–$1,000
F28335 / F28235 CSM 128-bit High (>85%) 5–10 days $600–$1,200
F28069 / F28069M CSM 128-bit High (>85%) 7–10 days $700–$1,200
F2837xD / F2837xS DCSM (Zone 1+2) Medium (50–75%) 10–15 days $1,500–$2,500
F28004x (F280049C, etc.) DCSM + optional EXEONLY Low–Medium (30–60%) 10–15 days $1,800–$3,000
F28002x / F28003x DCSM + optional EXEONLY Low–Medium (30–60%) 12–15 days $2,000–$3,000
F29H85x / AM263x Secure Boot + CMAC Not feasible N/A N/A

These ranges assume the chip is intact and not physically damaged. Decapped or reballed devices, or parts subjected to prior failed unlock attempts, may have lower success rates or require additional assessment fees.

What Determines Cost and Lead Time?

Three variables drive the final quote for a C2000 unlock engagement:

  • Protection generation: CSM-only parts are routine; DCSM parts require substantially more lab time and specialized tooling.
  • EXEONLY configuration: If the OEM enabled EXEONLY on critical sectors, semi-invasive techniques may be needed, increasing cost by 40–80% and adding 3–5 days.
  • Flash size and zone layout: A F2837xD with 1 MB of flash split across two zones takes longer to image and verify than a 128 KB F2802.

We provide a binding quote after a free feasibility assessment. If we determine the device cannot be unlocked, there is no charge. You ship the chip or the complete board; we return both the hardware and a verified binary image of the flash contents.

Our C2000 Unlock Process — Step by Step

  1. Intake & documentation: You submit the device part number, board photos, and proof of ownership or authorization. We verify the request is legitimate — see the authorization section below.
  2. Non-destructive assessment: We connect via JTAG/SWD to determine the exact CSM/DCSM state, zone configuration, and whether EXEONLY is active. This takes 1–2 days.
  3. Attack execution: Depending on the protection level, our engineers apply the appropriate technique — password recovery, glitch-based JTAG reactivation, or semi-invasive probing. The chip is not permanently altered in non-destructive approaches.
  4. Readout & verification: Flash contents are dumped sector by sector. We verify the image by comparing CRC checksums and, where possible, re-flashing to a blank device and confirming execution.
  5. Delivery: You receive the binary (.bin / .hex) image, a sector map, and your original hardware via tracked international shipping.

Authorization Requirements for C2000 Unlock

We perform C2000 unlock only for parties with legitimate rights to the firmware. Acceptable scenarios include:

  • You designed the firmware and lost the source code or build environment.
  • You own the product IP and the original developer is unavailable.
  • You need to maintain or repair legacy equipment you own, and replacement firmware is unavailable from the OEM.
  • You hold a written license or assignment from the IP holder.

We require a signed NDA and a declaration of ownership before starting work. Projects that cannot demonstrate authorization are declined. For more detail on our compliance framework, see our authorization and legal compliance policy.

Common Failure Modes and Honest Limitations

JTAG probe connected to a C2000 board during firmware unlock assessment

Not every C2000 unlock succeeds. Here are the situations where recovery is difficult or impossible:

  • EXEONLY properly enabled: Sectors marked EXEONLY in DCSM cannot be read back through any known non-destructive path. Semi-invasive methods sometimes work, but we quote these as low-probability engagements.
  • Blown JTAGLOCK fuse: Some F2837x and F28004x devices have a one-time-programmable fuse that permanently disables JTAG. If blown, our attack surface is reduced to the serial boot loader, which is slower and less reliable.
  • Physical damage: Chips with cracked die, corroded bond pads, or prior decapping attempts may be unrecoverable regardless of protection level.
  • Encrypted external flash: Some C2000 designs store additional code in external SPI flash encrypted with a key held in OTP. We can read the external flash, but decryption requires the OTP key — which circles back to the on-chip unlock problem.

We flag these risks during the free feasibility check so you can make an informed decision before committing budget.

C2000 vs. Other DSP/MCU Families

If you work with mixed-vendor boards, you may need unlock services for other controllers alongside your C2000. The protection difficulty varies widely:

  • Microchip’s PIC12 and PIC18 families use simpler code-protect fuses — see our PIC18 unlock and PIC12 unlock pages for details.
  • NXP’s Kinetis-K/L series employs flash security with a backdoor key mechanism similar in concept to CSM — covered on our Kinetis unlock page.
  • Renesas RX parts use ID-code protection with a 16-byte key, a different but comparable challenge — see Renesas RX unlock.

For boards combining a C2000 DSP with an STM32 or ESP32 co-processor, we can handle both devices in a single engagement, reducing total turnaround.

Deliverables You Receive

Deliverable Format Notes
Flash binary image .bin, .hex, or .out Full flash contents including OTP where readable
Sector map .csv / .xlsx Start address, size, zone assignment, EXEONLY status per sector
CSM/DCSM password Plain text Provided when recovered; allows you to re-unlock the same device
Verification report .pdf CRC checksums, readout log, any anomalies noted
Original hardware Physical return Tracked international shipping included

Frequently Asked Questions

Can you unlock a C2000 with EXEONLY sectors enabled?

It depends on the specific device and configuration. EXEONLY sectors on DCSM-equipped parts (F2837x, F28004x, F28002x) are designed to prevent any readback. In some cases, semi-invasive techniques can recover the contents, but we quote these as low-probability engagements — typically 30–40% success. We assess this during the free feasibility check before you commit.

Is C2000 unlock legal?

Yes, when performed for authorized purposes — recovering your own firmware, maintaining equipment you own, or working under a license from the IP holder. We require proof of ownership and a signed NDA before beginning any work. Unauthorized copying of third-party IP is something we decline. Our compliance and trust page explains the full process.

Do I need to ship the whole board or just the chip?

Either works. Shipping the complete board is often safer — desoldering a C2000 in a 176-pin LQFP or BGA package risks pad damage. If you do desolder the chip, use a hot-air station with proper thermal profiling and ship in an ESD-safe tray. We can also desolder it in our lab if you prefer.

What if my F28335 has a blank (all-ones) CSM password?

An all-ones password (0xFFFF…) means CSM was never intentionally programmed — the flash is effectively unsecured. In that case, you can read the device yourself via Code Composer Studio and a standard XDS-class JTAG probe. No unlock service is needed, and we will tell you that upfront rather than charge you.

How do you handle dual-zone DCSM on the F2837xD?

The F2837xD has two independent CPU subsystems, each with its own DCSM zone pair. We treat each zone as a separate unlock task. If both zones are locked, the cost and lead time increase accordingly — typically 1.5× to 2× the single-zone price. The feasibility assessment covers all zones.

Check feasibility for your project

Send the chip marking or board details and tell us what you need to recover. Add clear photos if available.

Request a feasibility review

Related IC Unlock Services

TURN THE GUIDE INTO A PROJECT QUESTION

What do you need to recover?

Send the full marking or board photos, sample condition and required outcome. Ask for an NDA before sharing confidential files. Scope and sample handling are confirmed individually.

The article title is carried into the contact form. Add your own details and review the enquiry before sending.

WhatsApp Send board details