Bao'An Shenzhen China

PIC10 Unlock | Feasibility, Cost & Lead Time

Oct 5, 2026  /  PCB COPY

pic10 unlock: PIC10F206 SOT-23 microcontroller on an ESD mat ready for firmware recovery

What Is PIC10 Unlock and When Do You Need It?

PIC10 unlock is the process of recovering firmware from code-protected Microchip PIC10F and PIC10LF microcontrollers. These tiny 6-pin or 8-pin baseline and mid-range devices are found in sensor nodes, LED drivers, battery monitors, and single-function control boards. When the original source code is lost, the design engineer has left the company, or a legacy product needs maintenance, authorized firmware readout is often the only path forward. Our lab handles PIC10 unlock requests regularly, with a typical turnaround of 5–10 working days and success rates that vary by specific part number and silicon revision.

PIC10 Family Overview — What You’re Actually Dealing With

pic10 unlock: PIC10F206 SOT-23 microcontroller on an ESD mat ready for firmware recovery

The PIC10 designation covers two distinct architecture tiers inside Microchip’s portfolio. Understanding which tier your device belongs to determines the protection scheme, the attack surface, and ultimately whether an unlock is feasible.

Baseline Core (12-Bit Instruction)

Parts like the PIC10F200, PIC10F202, PIC10F204, and PIC10F206 use a 12-bit instruction set with a single code-protection (CP) fuse bit. Flash sizes range from 256 to 512 words. These devices lack EEPROM, and their protection mechanism is relatively straightforward — clearing CP erases program memory on most revisions, but physical-layer techniques can recover content before the erase completes on certain silicon lots.

Enhanced Mid-Range Core (14-Bit Instruction)

The PIC10F320, PIC10F322, PIC10LF320, and PIC10LF322 moved to the enhanced mid-range core with 14-bit instructions, 256–512 words of flash, and a more granular configuration word. The CP bit still guards the entire code space, but the internal bus architecture is tighter, and some revisions added additional timing checks during ICSP reads.

Part Number Core Flash (Words) Pins Protection Unlock Feasibility
PIC10F200 Baseline 12-bit 256 6 (SOT-23) Single CP bit High
PIC10F202 Baseline 12-bit 512 6 (SOT-23) Single CP bit High
PIC10F204 Baseline 12-bit 256 6 (SOT-23) Single CP bit High
PIC10F206 Baseline 12-bit 512 6 (SOT-23) Single CP bit High
PIC10F320 Enhanced Mid-Range 256 6/8 CP + WRT bits Moderate–High
PIC10F322 Enhanced Mid-Range 512 6/8 CP + WRT bits Moderate–High
PIC10LF320 Enhanced Mid-Range 256 6/8 CP + WRT bits Moderate–High
PIC10LF322 Enhanced Mid-Range 512 6/8 CP + WRT bits Moderate–High

How Does PIC10 Code Protection Work?

Code protection on PIC10 devices is controlled by one or two configuration bits written during programming. When CP is set to “ON,” the device blocks external read commands through the ICSP (In-Circuit Serial Programming) interface. On baseline parts, attempting a read returns all zeros or all ones. On enhanced mid-range parts, the device may return the configuration word and device ID but masks the program memory contents.

Critically, PIC10 chips lack the multi-zone, multi-level protection found on larger Microchip families like PIC24E devices with segmented code guard or PIC32MZ parts with secure boot features. The PIC10’s simplicity — a single global CP bit protecting a few hundred words — is precisely what makes firmware recovery feasible in the majority of cases.

What Can Go Wrong

  • Late-revision silicon: Microchip periodically updates mask sets. A PIC10F322 from 2022 may have a different internal layout than one from 2015. We always request the date code and revision letter before committing to a timeline.
  • Damaged die: SOT-23 packages are fragile. If the chip was exposed to ESD events, moisture damage, or desoldering heat above 280 °C for extended periods, the die may be physically compromised.
  • OTP variants: Some PIC10F200/202 parts shipped in OTP (one-time programmable) packages. These use a different memory technology and require a modified approach.

Our PIC10 Unlock Process — Step by Step

Every PIC10 unlock engagement follows a structured workflow designed to protect your device, your data, and your IP rights.

  1. Feasibility assessment (1–2 days): You submit the exact part number, date code, package type, and proof of ownership or authorization. We confirm whether the specific revision is within our capability set.
  2. Device receipt and inspection: We examine the chip under magnification, verify markings, and confirm the package is intact. For SOT-23 parts, we check for micro-cracks from desoldering.
  3. Non-invasive probing: We first attempt ICSP-level techniques — voltage glitching, timing manipulation, and protocol-edge analysis — that do not require decapping.
  4. Semi-invasive / invasive recovery (if needed): For resistant revisions, we decap the package using fuming nitric acid, expose the die, and use micro-probing or UV-based techniques to neutralize the CP fuse without erasing flash.
  5. Verification and delivery: Extracted firmware is verified by programming it into a blank PIC10 of the same part number and comparing functional behavior. You receive a .hex file and a brief analysis report.

Authorization is required at step one. We operate under NDA and only accept jobs where the client demonstrates legal ownership of the design or device. For details on our compliance framework, visit our trust and authorization policy.

PIC10 Unlock Cost and Lead Time

Pricing depends on the specific part, silicon revision, and whether non-invasive methods succeed on the first attempt. Below are representative ranges — not fixed quotes.

Device Tier Typical Cost (USD) Lead Time (Working Days) Notes
PIC10F200/202/204/206 (baseline) $300 – $600 5 – 8 High success; non-invasive usually sufficient
PIC10F320/322 (enhanced mid-range) $400 – $900 7 – 12 Revision-dependent; may need decapping
PIC10LF320/322 (low-voltage) $400 – $900 7 – 12 Same die as F-series but tighter voltage margins
Rush service (any PIC10) +40–60% surcharge 3 – 5 Subject to lab availability

We charge a non-refundable evaluation fee (typically $50–$100) that is credited toward the full job if you proceed. If the unlock fails, you pay only the evaluation fee — no success, no charge for the recovery portion.

Check feasibility for your project

Send the chip marking or board details and tell us what you need to recover. Add clear photos if available.

Request a feasibility review

When PIC10 Unlock Is — and Isn’t — the Right Move

Lab workstation set up for PIC10 microcontroller decapping and firmware readout

PIC10 unlock makes sense when you need to recover firmware you own but no longer have in source form. Common scenarios include:

  • Legacy product still in production but the original developer is unavailable.
  • Reverse engineering your own prototype for a redesign onto a newer MCU.
  • Failure analysis — comparing extracted code against a known-good build to identify field corruption.
  • Second-sourcing a board assembly where the programmed MCU is the bottleneck.

It is not a substitute for proper version control. If you’re designing new products on PIC10, invest in a secure code repository now. The cost of a single unlock exceeds a decade of Git hosting.

PIC10 vs. Other Microchip Families — Comparative Difficulty

If you work across the Microchip ecosystem, it helps to understand where PIC10 sits on the difficulty spectrum relative to other families we handle.

Family Protection Complexity Typical Unlock Difficulty
PIC10 (baseline/enhanced) Low — single CP bit Low–Moderate
PIC14 (mid-range) Low–Medium — CP + optional WRT Moderate
PIC17 (high-end 8-bit) Medium — multi-word config Moderate–High
PIC24E / PIC24H High — Code Guard Security High
PIC32MZ Very High — secure boot + encryption Very High

The PIC10’s minimal protection is both a blessing (high feasibility) and a reflection of its role: these are tiny utility controllers, not security-critical processors.

What You’ll Receive After a Successful PIC10 Unlock

  • Intel HEX file (.hex) — the complete program memory contents, ready to program into a blank PIC10 using MPLAB IPE or any compatible programmer.
  • Configuration word dump — oscillator selection, watchdog settings, MCLR configuration, and code-protect bits as extracted.
  • Optional disassembly listing — annotated baseline or mid-range assembly, helpful if you plan to modify or port the firmware. Available for an additional fee.
  • Verification report — confirmation that the extracted image was programmed into a test device and passed functional checks.

Preparing Your PIC10 for Shipment

To maximize the chance of a clean extraction:

  1. If the chip is still on a PCB, desolder it carefully at ≤260 °C with a hot-air station. Avoid prolonged heat on SOT-23 packages.
  2. Place the device in an ESD-safe tube or foam. Do not use conductive foam that could short pins.
  3. Include a note with the full part number (e.g., PIC10F206-I/OT), the date code printed on the package, and your authorization documentation.
  4. Ship via a tracked carrier. For international shipments, declare as “electronic component samples” with a low customs value.
Can every PIC10 variant be unlocked?

Most PIC10F and PIC10LF variants have high unlock feasibility, especially baseline 12-bit parts (PIC10F200–206). Enhanced mid-range parts (PIC10F320/322) depend on silicon revision. We assess each device individually and will tell you upfront if a particular revision is outside our current capability. The evaluation fee covers this assessment.

Is PIC10 firmware extraction legal?

Recovering firmware from a microcontroller you own — or are authorized to service — is legal in most jurisdictions. We require proof of ownership or a signed authorization letter before starting work. All projects are covered by NDA. We do not assist with extracting third-party proprietary code without documented permission.

Will the original PIC10 chip survive the unlock process?

Non-invasive methods (voltage glitching, timing attacks) leave the device fully functional. If semi-invasive decapping is required, the chip is destroyed during the process. We recommend sending at least two samples when possible — one for extraction and one as a backup. For baseline parts, non-invasive success is common, so the chip often survives intact.

How does PIC10 unlock compare in cost to larger Microchip MCUs?

PIC10 devices are among the least expensive to unlock in the Microchip portfolio, typically $300–$900 depending on the variant. By comparison, PIC24H unlock or PIC32 recovery can cost significantly more due to multi-layer code guard and encrypted boot features. The PIC10’s small flash and simple protection keep costs low.

Can you port the recovered PIC10 firmware to a different MCU?

Yes. After extraction, our engineers can disassemble and annotate the baseline or mid-range assembly code, then assist with porting to a newer part — such as a PIC16 or even an ARM Cortex-M0 — if you’re redesigning the product. This is quoted as a separate engineering service.

Check feasibility for your project

Send the chip marking or board details and tell us what you need to recover. Add clear photos if available.

Request a feasibility review

Working on a board like this?

Send the chip marking or two photos. You get feasibility, lead time and price within 24 hours, and the check costs nothing.

Get a free quote

Related reading

WhatsApp Send board details