What Does STM32F1 Crack Actually Mean?
An STM32F1 crack is the process of bypassing the read-out protection (RDP) on STMicroelectronics’ STM32F1xx-series Cortex-M3 microcontrollers to extract the firmware stored in on-chip flash. The STM32F1 family — including the widely deployed STM32F103C8T6, STM32F101, and STM32F107 — uses a two-tier RDP scheme (Level 1 and Level 2) that determines whether recovery is feasible. At RDP Level 1, authorized firmware readout is achievable in most cases with a typical turnaround of 5–10 working days. At RDP Level 2, the protection is permanent and no known non-destructive method can recover the flash contents.
STM32F1 Read-Out Protection Levels Explained

The STM32F1 series implements RDP through option bytes stored in a dedicated flash area. Understanding the three states is essential before any recovery attempt.
| Protection State | RDP Byte Value | Debug Access | Flash Read via SWD/JTAG | Recovery Feasible? |
|---|---|---|---|---|
| Level 0 (No Protection) | 0xA5 | Full | Yes | Trivial — standard readout |
| Level 1 (Read Protection) | Any value ≠ 0xA5 and ≠ 0xCC | Limited | No (mass-erase on unlock) | Yes — specialized techniques |
| Level 2 (Permanent Lock) | 0xCC | Disabled permanently | No | Not feasible non-destructively |
Most production STM32F1 boards ship at RDP Level 1. Level 2 is irreversible — once set, even ST’s own factory tools cannot downgrade it. Our engineers verify the RDP state as the first step in every STM32L4 and broader STM32 recovery engagement, because the answer dictates the entire approach.
Why STM32F1 RDP Level 1 Is Crackable
RDP Level 1 on the STM32F1 disables external flash reads through the debug interface and blocks boot-mode readout, but it does not disable all internal execution paths. Several characteristics of the F1’s Cortex-M3 implementation and flash controller create openings:
- Voltage glitching window: The STM32F1’s flash access controller checks RDP status during specific clock cycles. A precisely timed supply-voltage transient (typically 5–50 ns wide, dropped to 0.8–1.5 V on VDDA) can cause the RDP comparator to misread the option byte, temporarily granting debug access without triggering mass erase.
- Boot ROM behavior: The built-in system bootloader in early STM32F1 revisions (Rev A, Rev Z on some F103 parts) has known timing-sensitive paths that can be exploited before the flash lockout takes effect.
- JTAG/SWD race conditions: On certain silicon revisions, issuing a halt command within the first few microseconds after reset — before the RDP enforcement logic activates — allows a partial flash dump.
None of these techniques work against Level 2. The option byte 0xCC permanently fuses the debug port shut at the hardware level.
Silicon Revision Matters
STMicroelectronics has shipped at least six silicon revisions of the STM32F103 alone (Rev A through Rev Z, Rev Y, Rev 1, etc.). Each revision patches some glitch vectors while sometimes introducing new side-channel behaviors. Our lab maintains a revision-specific database covering over 40 STM32F1xx part numbers. When you submit a chip, we identify the die revision via the DBGMCU_IDCODE register (address 0xE0042000) before selecting an attack profile.
Step-by-Step: How Our Engineers Perform an STM32F1 Crack
1. Intake and Authorization Verification
We require proof of ownership or written authorization before starting any firmware recovery. This includes purchase records, design files, or a signed letter from the IP holder. Every engagement runs under NDA. This policy protects both parties and keeps the work within the same legal framework we apply to STM32G4 and other STM32 recovery projects.
2. RDP Level Identification
The chip is connected to an ST-Link V2 or J-Link probe. We attempt a standard SWD connection. If the debugger reports “readout protection active,” we read the option bytes through indirect methods to distinguish Level 1 from Level 2. A Level 2 chip is returned to the client with a detailed report — we do not attempt destructive decapsulation for firmware recovery on permanently locked parts.
3. Glitch Parameter Calibration
For Level 1 parts, we mount the chip on a custom test jig with precision voltage injection. Key parameters:
- Glitch voltage: 0.8 V – 1.6 V (part-dependent)
- Glitch width: 5 ns – 80 ns
- Trigger offset from reset edge: 1 µs – 200 µs, swept in 50 ns increments
- Core supply (VDD): held at 3.3 V ± 50 mV during normal operation
The calibration sweep typically runs 10,000–500,000 iterations. A successful glitch produces a valid 32-bit word from flash address 0x08000000 (the reset vector). Once one word reads correctly, we lock the parameters and dump the full flash in 1 KB blocks.
4. Flash Dump and Verification
The extracted binary is verified with a CRC-32 check against the chip’s own flash CRC peripheral (where available) and by disassembling the vector table to confirm valid Cortex-M3 exception handlers. We deliver the firmware as a raw .bin file and an Intel HEX (.hex) file, both with a SHA-256 hash for integrity.
Which STM32F1 Parts Are Covered?
| Sub-Family | Example Parts | Flash Size Range | RDP L1 Recovery | Notes |
|---|---|---|---|---|
| STM32F100 (Value Line) | STM32F100C8, STM32F100RB | 16 KB – 128 KB | High success | Older silicon, wider glitch window |
| STM32F101 | STM32F101C8, STM32F101RB | 16 KB – 512 KB | High success | — |
| STM32F102 | STM32F102C8 | 64 KB – 128 KB | High success | USB device line |
| STM32F103 | STM32F103C8T6, STM32F103RCT6, STM32F103ZET6 | 16 KB – 512 KB | High success | Most common F1 target |
| STM32F105/107 | STM32F105RCT6, STM32F107VCT6 | 64 KB – 256 KB | Moderate | Connectivity line; tighter timing on newer revisions |
For parts with 512 KB flash (high-density devices), the dump takes longer — roughly 2–4 minutes per successful glitch cycle versus under 30 seconds for 64 KB parts — but the success rate remains comparable.
What Can Go Wrong

Honest engineering means acknowledging limits. Here are realistic failure scenarios:
- RDP Level 2 confirmed: No recovery possible. We’ve seen mislabeled boards where the developer set Level 2 thinking it was Level 1.
- Damaged flash cells: Chips pulled from equipment that experienced over-voltage events or long-term high-temperature operation (>105 °C ambient) may have degraded flash. Readout succeeds but certain pages return 0xFF or corrupted data.
- Remarked / counterfeit parts: Some chips sold as STM32F103C8T6 are actually CKS32F103C8T6 or GD32F103C8T6 clones. These use different flash controllers and RDP implementations. We can often still recover firmware, but the glitch parameters differ significantly. We identify clones via the DBGMCU_IDCODE and silicon wafer markings under microscope.
- Code-readout-protection combined with write-protection: Some developers also set WRP (write-protect) bits. This doesn’t block our recovery but complicates the option-byte manipulation step.
STM32F1 Crack vs. Other STM Families
The STM32F1 is generally easier to recover than newer STM32 families because its Cortex-M3 core and flash controller predate many of ST’s hardened RDP countermeasures. For comparison:
- The STM32L0 series uses a similar two-level RDP but with tighter glitch windows due to its ultra-low-power flash design.
- STM32L4 parts add PCROP (proprietary code readout protection) on top of RDP, creating an additional layer to bypass.
- Legacy 8-bit STM8S microcontrollers use a simpler ROP (readout protection) bit that behaves differently from the 32-bit RDP scheme.
If your project involves a mix of STM families on the same board, we handle multi-chip recovery as a single engagement.
Turnaround, Deliverables, and Pricing Signals
Standard STM32F1 crack projects complete in 5–10 working days from chip receipt. Rush service (3 working days) is available for production-critical situations. Deliverables include:
- Raw firmware binary (.bin) and Intel HEX (.hex)
- SHA-256 hash verification report
- Option byte dump (including RDP, WRP, and user-data bytes)
- Silicon revision identification report
Pricing depends on the specific sub-family, flash size, and silicon revision. Contact us with your part number for an exact quote.
Check feasibility for your project
Send the chip marking or board details and tell us what you need to recover. Add clear photos if available.
Request a feasibility reviewFrequently Asked Questions
Can an STM32F1 at RDP Level 2 be cracked?
No. RDP Level 2 permanently disables the debug interface by blowing internal fuses. No voltage glitch, laser fault injection, or software exploit can reverse this on STM32F1 parts. If your chip is confirmed at Level 2, the firmware cannot be recovered non-destructively. We verify the level before beginning work and will report a Level 2 finding immediately.
Will the STM32F1 crack erase my firmware?
Our glitch-based approach reads flash contents without triggering the mass-erase sequence that a normal RDP downgrade would invoke. The chip’s flash remains intact after extraction. However, we recommend keeping the original chip unmodified as a backup until you’ve verified the delivered binary.
Do you need the whole PCB or just the chip?
We prefer the chip desoldered from the board (QFP-48 or QFP-64 package, depending on the part). If desoldering isn’t practical, send the entire PCB and our technicians will remove the chip. Either way, the chip is returned to you after recovery along with the firmware files.
Is STM32F1 firmware recovery legal?
Authorized firmware recovery — recovering code you own, code from your own product design, or code where the IP holder has given written permission — is legal in most jurisdictions. We require proof of authorization before every engagement and operate under NDA. We do not perform recovery for the purpose of copying third-party proprietary firmware.
How do I know if my STM32F103 is genuine or a clone?
Read the DBGMCU_IDCODE register at 0xE0042000. Genuine ST parts return device IDs documented in ST’s reference manual (e.g., 0x20036410 for medium-density F103). Clones from GigaDevice or CKS return different IDs. If you can’t access the debug port due to RDP, send us the chip and we’ll identify it during intake. Clone identification is included at no extra charge.
Related MCU Recovery Services
- STM32G4 firmware recovery — mixed-signal Cortex-M4F parts with enhanced RDP
- STM8S readout protection bypass — 8-bit STM legacy MCUs
- EFM32 flash extraction — Silicon Labs Cortex-M parts with AAP lock
- AT89C51 lock-bit recovery — classic 8051-architecture Atmel MCUs
Working on a board like this?
Send the chip marking or two photos. You get feasibility, lead time and price within 24 hours, and the check costs nothing.
Get a free quote